how to install peel and stick tile in bathroom around tub

#How to install peel and stick tile in bathroom around tub full#

Slide the cutter's adjustable fence against the edge of the tile so that you can cut the remaining tiles without marking each one.

Place the tile to be trimmed on the tile cutter so the mark lines up with the cutting wheel.

#How to install peel and stick tile in bathroom around tub full#

Where the tiles need to be cut to fit against a corner or ceiling, hold a full tile in place and mark where it overlaps the last full tile already on the wall.If your tiles aren't self-spacing, use plastic spacers to maintain consistent joints. Many tiles have small nubs on the edges to keep them evenly spaced at the proper width for grout.Continue setting tiles in both directions along the two lines, working out toward the end wall and down to the tub in a stepped pattern.Pro2ProTip: Make sure to leave space for caulk between the bottom course of tile and the tub. Start at the intersection of the two layout lines and spread a thick layer of tile mastic onto one quadrant of the wall with the smooth edge of a trowel.If this leaves tile slivers on both sides, adjust the line right or left as necessary.Ģ. Divide this dimension in half and draw a plumb line down the center of the wall. Next, measure the width of the back wall horizontally.Using a level, draw a horizontal line across the wall at this mark. If you end up with less than half a tile at the tub, adjust the mark downward by the height of this partial tile so you end up with a full tile at the bottom and a larger cut tile at the top. Calculate how many tiles it takes to reach from the center mark down to the tub. Check if you need to adjust this mark to avoid laying slivers of tile at the top and bottom.Divide the dimension in half and make a mark there. To tile around a tub or shower, start by measuring the height of the back wall from the lip of the tub to the top of the area to be tiled.Tiling Around a Tub Shower Overview Gregory Nemec Mastic is much stickier than mortar, so you won’t have to worry about the tiles sliding down the wall. Ferrante glued the tiles to the backer board with latex tile mastic, not thinset mortar. However, the methods shown here work on any wall tiles, including stone and glass. Finally, to ensure a strong, long-lasting bond for the new tiles, Ferrante goes one step further and trowels thinset mortar over the entire wall.įor this installation, Ferrante used 4¼-inch-square ceramic tiles, the most common and easiest-to-install bath tiles. He then fills the backer board seams with thinset mortar and embeds fiberglass-mesh joint tape in the mortar. The first and most important step for tiling bathroom walls insists Ferrante, is to start with a clean, stable substrate.

With the right tools and materials-and the patience to lay out the tiles properly-tiling a shower or bath surround is a job that most homeowners can pull off.įor the project shown here, we enlisted the help of tile contractor Joe Ferrante, who has been laying tile for This Old House projects since 1986. The floor tiles added the perfect color pop to their bathroom, and we’ll for sure keep you posted on how it wears over time.Tile is the most popular choice for walls in new and remodeled baths because it’s impervious to water, extremely stain-resistant, easy to clean, and available in dozens of colors, sizes, and styles. So if you want to tackle this yourself–for sure watch this video! We thought it would be most helpful to document and share the process (and mistakes! haha) through a video. We opted to keep the grout lines exposed to make it look even more realistic and I love LOVE LOVE the way it turned out. The vinyl was thin (a little thicker than peel and stick wallpaper) so it really sits snug to the floor tiles, even though ours were anything but smooth to start with. You could easily use a straight edge and razor, too. Speaking of the cuts, we used this paper cutter to make quick work of any trimming that needed done around the edges. Chris had a meeting and came to help with the cuts when he was done. It took maybe 2.5 hours to do the whole floor and that was me mostly doing it alone. It was a very EASY, painless and pretty quick. They come in different sizes and scale–we did the 12″ (since that is what size our tile was) in the quarter scale. I fell hard for these rust colored vinyl floor tiles (they’re waterproof!) when I saw them on Etsy and ordered enough to cover each square tile in the girls’ bathroom. One thing I love about a phase 1 is it’s a great way to try something bold. Added beadboard to the walls and last week, we laid peel and stick vinyl tile over the existing tile floors. We have been doing a quick phase 1 renovation of the girls’ bathroom (read more about the plans here!) over the last week and it’s coming along so well! We painted the countertops last week using the same countertop paint (and color–Putty!) as we used in our kitchen in our first house nearly a decade ago.